对于经常使用河北升降货梯http://www.rgsjpt.com/的朋友来说，河北升降货梯主要由导轨架、起升机构、物料平车、附着装置、安全装置及电气设备等组成。同时大家也知道选购河北升降货梯的时候，其安全性是最重要的。河北升降货梯要承载一定量的物资和人身，跨越的高度也是很大的。
1、河北升降货梯导轨架采用2根10号槽钢作为导轨架标准节主肢，用1英寸管为腹杆。每节标准节的长度为2500mm，在满足强度要求的前提下，将标准节设计为片式结构，以方便运输和安装。每两节标准节之间用折弯联板在槽钢内侧进行联接，槽钢外表面必须平直，以确保物料河北升降货梯运行平稳。
Shandong cargo lifter guide frame with two on the 10th channel as a guide rack standard section main limb, with 1 inch tube webs. The length of each section of the standard section of 2500mm, to meet the strength requirements under the premise of the standard section is designed to piece structure for easy transportation and installation. Each section between the two standards associated with the bending plate in the inside channel to connect as the outer surface of the channel must be straight, in order to ensure the smooth running of material Shandong cargo lifter.
  
2、河北升降货梯起升机构放置在导轨架标准节底节上，以方便其安装、接线、调试和日常维护等工作。在标准节的顶节上设置有一个定滑轮，起升钢丝绳经其穿绕后向下拉伸并固定在液压升降机上，以提升物料平车，运送施工物料并将施工层的废料等运至地面。
Shandong cargo lifter lifting mechanism is placed on the bottom rail frame section standard section, in order to facilitate its installation, wiring, commissioning and routine maintenance work. It is provided with a fixed pulley lifting rope through stretching and fixed on a hydraulic lift after winding down after it, to enhance the material flat car, transport of construction materials and construction waste layer on the top section of the standard sections, etc. into ground.
   
3、河北升降货梯http://www.rgsjpt.com/起升机构选用减速电机，电机轴线与输出齿轮成L形输出，使起升机构体积达到最小，方便布置及运输。同时设置一级开式传动齿轮，一方面可增大减速比，另一方面也可使减速机位置相对于卷筒中心向后移动，可使起升机构整体安装便捷。河北升降货梯主梁上设有导向滚轮。为减小滚轮压力，同时为了保障提升河北升降货梯护栏有一定的防护高度，将上下导向滚轮距离设定为其结构范围内的最大值，使物料平车有一定的导向高度，使车轮受力合理，运行更平稳。
Shandong cargo lifter hoisting mechanism chosen geared motor, the motor axis with the output gear to the L-shaped output, allowing the lifting mechanism to a minimum volume, convenient arrangement and transportation. While setting level open drive gear, one can increase the speed reduction ratio, on the other hand also allows gear position relative to the roll center moves backward, lifting mechanism allows easy installation as a whole. Shandong cargo lifter main beam with a guide wheel. To reduce the pressure roller, and in order to enhance protection of Shandong Huoti have some protective fence height, distance between the upper and lower guide roller is set within a maximum range of its structure,the material has a certain orientation flat car height, the wheel force reasonable, run more smoothly.